Experimental investigation on the invert stability of operating railway tunnels with different drainage systems using 3D printing technology

In recent years, the invert anomalies of operating railway tunnels in water-rich areas occur frequently, which greatly affect the transportation capacity of the railway lines. Tunnel drainage system is a crucial factor to ensure the invert stability by regulating the external water pressure (EWP). By means of a three-dimensional (3D) printing model, this paper experimentally investigates the deformation behavior of the invert for the tunnels with the traditional drainage system (TDS) widely used in China and its optimized drainage system (ODS) with bottom drainage function. Six test groups with a total of 110 test conditions were designed to consider the design factors and environmental factors in engineering practice, including layout of the drainage system, blockage of the drainage system and groundwater level fluctuation. It was found that there are significant differences in the water discharge, EWP and invert stability for the tunnels with the two drainage systems. Even with a dense arrangement of the external blind tubes, TDS was still difficult to eliminate the excessive EWP below the invert, which is the main cause for the invert instability. Blockage of drainage system further increased the invert uplift and aggravated the track irregularity, especially when the blockage degree is more than 50%. However, ODS can prevent these invert anomalies by reasonably controlling the EWP at tunnel bottom. Even when the groundwater level reached 60 m and the blind tubes were fully blocked, the invert stability can still be maintained and the railway track experienced a settlement of only 1.8 mm. Meanwhile, the on-site monitoring under several rainstorms further showed that the average EWP of the invert was controlled within 84 kPa, while the maximum settlement of the track slab was only 0.92 mm, which also was in good agreement with the results of model test.     

Liner services network design and fleet deployment with empty container repositioning

Transportation demand of shipping container fluctuates due to the seasonality of international trade, thus, every 3–6 months, the liner company has to alter its current liner shipping service network, redeploy ships and design cargo routes with the objective of minimizing the total cost. To solve the problem, the paper presents a mixed integer linear program model. The proposed model incorporates several relevant constraints, such as weekly frequency, the transshipment of cargo between two or more service routes, and transport time. Extensive numerical experiments based on realistic date of Asia–Europe–Oceania shipping operations show that the proposed model can solve real-case problems efficiently by CPLEX. The results demonstrate that the model can reduce ship’s capacity consumption and raise ships’ capacity utilization.     

小型机载激光通信系统设计与验证

针对空空宽带高速通信的需求，设计了小型化机载激光通信系统。仿真分析了300 km、2.5 Gb/s无线激光链路性能，并通过运动仿真台模拟机动环境测试了系统的跟踪与通信性能，其中粗跟踪误差为533.2 μrad(1σ)，精跟踪误差为3.6 μrad(1σ)，测试数据传输240 s，通信误码率为2.82×10-9。仿真与实验验证了该系统用于远距离空空无线激光通信的可行性。     

TRIZ理论在集装箱吊具旋锁机构中的设计应用

利用TRIZ理论,采用因果分析现有结构中缺陷与不足产生的原因。在分析了整个集装箱吊具旋锁机构的系统组件模型后,利用因果分析寻找产生的原因。针对不同的问题采用不同的TRIZ解题工具分别运用技术矛盾、物质—场分析、进化分析对旋锁机构进行创新方案的设计。     

基于液压活塞式惯容器的车辆悬架性能研究

阐述了液压活塞式惯容器的基本结构、工作原理与承载力大的特点，建立了考虑摩擦力、寄生阻尼力和油液弹性效应的惯容器非线性力学模型。在数控液压伺服激振台上对液压活塞式惯容器进行了力学性能试验，基于试验结果，利用Matlab参数辨识工具箱对非线性力学模型中的参数进行辨识。在此基础上建立了包含液压活塞式惯容器非线性因素的车辆惯容器 弹簧 阻尼器（inerter-spring-damper，简称ISD）悬架动力学模型并进行了仿真分析。结果表明，当考虑液压活塞式惯容器非线性因素时，车辆ISD悬架系统的车身加速度均方根值增加5%，而轮胎动载荷与悬架动行程均方根值均有所减小,降低了车辆的行驶平顺性。     

接轨站设置位置和布置图型的影响因素及其分类

通过对接轨站设置位置和布置图型主要影响因素的分析。按照能够充分反映接轨站作业特点的交接方式。对接轨站所采用的布置图型进行了归纳和分类。     

某雷达数据处理有关问题分析

对某雷达数据处理应用中存在的一些特殊问题进行讨论分析,并就具体问题提出了解决的方法.     

毗邻铁路大动脉排架式厂房拆除爆破

文章介绍了运煤车间爆破拆除工程的设计、施工经过及防后座的措施，对于复杂爆破环境的建筑物拆除有一定参考意义。     

浅谈延迟焦化装置露天栈桥的设计

根据延迟焦化装置露天栈桥的工程设计实践,围绕一炉两塔(一个加热炉两个焦炭塔)的焦化装置,分析了露天栈桥设计中的要点及难点,对其在平面布置、基础安排和吊车梁选型等设计方面做一些介绍和论述。     

主动雷达终端实时仿真软件的设计与实现

在主动雷达数据回放显示的基础上,通过使用D irectDraw和Intel IPP技术,设计了主动雷达终端实时仿真软件,包括信号处理、数据处理及终端显示等模块,极大地提高了软件的执行效率,使得整个仿真过程具有良好的实时性。本文介绍了该软件的设计及实现。